Repositionimg the kicker mount

One of the issues with fitting a chief powerplant into a 101 chassis is that the kicker stud is too close to the pinion... Today i made a start on repositioning the stud.
First off i drilled a piece of flat 1/4" stock to fit snugly over the existing 101 stud



With a length of 7/8" roundstock as a kicker pivot i offered the kicker up into position so the teeth mesh but not too tightly



Having marked the centre of the stud i drilled a 1/2" hole and turned the roundstock down on the lathe to the same size


With the new pin loosely in position i marked it with room for a washer and circlip then parted it off


All clamped together ready to weld now.

- Posted using BlogPress from my iPhone

Made to measure

- Posted using BlogPress from my iPhone

Finally got the powerplant fitted in the chassis

Engine plates and spacer tube



Change of plan... I decided that the tanks fit nicer over the backbone of the frame



And at close of business this afternoon ...



- Posted using BlogPress from my iPhone

Rollin Rollin Rollin......

- Posted using BlogPress from my iPhone

Odd Jobs

Cleaned up the old Yamaha tls hub and trued it up on the old crappy chrome 18" wheel that it came with... It will get built into a new rim once I have decided whether to run an 18",19" or 21" rim up front






All done while the paint dries



- Posted using BlogPress from my iPhone

Bars

I picked up a modified '30s chief bar centre during the gathering stages of the project, it had solid round bar stubs welded either side ( slightly squint!!!) to take risers and aftermarket bars.
Today i set it up in the lathe turned down the stubs to the same diameter as the inside of a set of old Triumph 1" western pattern bars that i got from Tony with the 101 frame.






A couple of cuts later


And they are ready for welding




- Posted using BlogPress from my iPhone

Crossbar... all welded and ground back

Thats the frame ready to come out of the jig and get a coat of primer or two


- Posted using BlogPress from my iPhone

'33 heads on '40 jugs

Make for a lot more room up top.








- Posted using BlogPress from my iPhone

Progress 3

- Posted using BlogPress from my iPhone

Progress 2

Revised steel plugs internally bored to 3/4" to cut down on excess weight, outer diameter 1.125" to match factory spec tube






- Posted using BlogPress from my iPhone

Progress

A bit of time in the engine room on the lathe today and the cross brace is ready to be welded in place
















- Posted using BlogPress from my iPhone

Frame mods Plan C ref 5.5 revision F

I looked at the flat plate template this morning, cut out the shape in rough from a length of 8"x1/4" flat stock ... Picked it up and decided it had no place on a hotrod motocycle.....
Change of plan. Length of 7/8" tube in the lathe, squared off at both ends and cut back at 45 deg. Then i cut 2 end slugs with 3/8" dowels to fit into 1/2"x1" flat drops, which will be countersunk and bolted to the 1" slugs fitted to the frame.




















- Posted using BlogPress from my iPhone

Progress

Started the day with a modified plywood mock up of the removable flitch plate to replace the crossbar



Then i found a length of 1.25" screwed rod in the railway yard and turned down a short length to use as slugs in the frame, to fut the plate in place



As i was doing that, a courier arrived with the blower, so i trial fitted it to see if it would go where i want it.... all fits in fine 8)




- Posted using BlogPress from my iPhone

Frame crossbar

After having a long look and think about how best to replace the under tank crossbar, today i mocked up option two in Grizzy's sketch below







The steel version will extend 3" forward and pick up a fixing from the web of the front headstock casting, a fourth fixing will drop vertically from just in front of the seat hinge mount and pick up the headsteady




This will give 1.5" of clearance between the tanks to let me move the oil line fittings in there and aid cooling!

- Posted using BlogPress from my iPhone

Seat n feet

Picked up a package from parcelforce this morning that had come from Australia, complete subframe for my Messinger seat, sits a bit too far forward and high for my taste so I'll need to make up a longer front pivot bar and the spring mounts... once the rear guard is fitted.
Cast alloy scripted footboards c/o Tony @ Indian Trading










Posted using BlogPress from my iPhone

Blower and SU

Picture of a blown 1936 MG ta that pulled up outside the shop last week have got me thinking.....







1250cc motor 1.5" SU and a Shorrock supercharger, my concerns about reliability dispelled by the driver who told me he was touring around tje coast of Scotland!


- Posted using BlogPress from my iPhone

The first cut!

With the Sport Scout away for the day at the MOT station in Inverness. I decided today would be a good day to cut the crossbar out of the 101 frame and see if i could get the motor sitting in nicely
















Just as i was fitting the tanks this beaut of a 1936 MG TA pulled up! More pics of it on the Speedshop blog.


Posted using BlogPress from my iPhone